How do I reset my Weiser Powerbolt 2?

How do I reset my Weiser Powerbolt 2?

How to restore default settings on my Powerbolt 2? Perform a factory reset

  1. Make sure the door is open and unlocked.
  2. Enter the default Mastercode (O-O-O-0).
  3. Press the lock button.
  4. Press 0.
  5. Press the lock button.
  6. Test the lock: With the door open and unlocked, Press the lock button.

How do I unlock my Weiser Powerbolt?

Press and hold the Reset button on the interior assembly for 5 seconds, until you hear 3 long beeps. Align the colored edges of the connectors and ensure a tight cable connection. IMPORTANT: Rotate the turnpiece AWAY from the door edge and make sure the latch is fully retracted (in the unlocked position).

How do you reprogram a Weiser deadbolt?

Note: Programming instructions can also be found on interior of lock.

  1. a. Press the program button on the interior unit once.
  2. b. Enter in 4 to 8 digit code onto the keypad.
  3. c. Press the “LOCK” button to save code.
  4. d.
  5. a. Press the program button on the interior unit twice.
  6. b.
  7. c.
  8. d.

What is Weiser master code?

The mastercode is required to put the lock in programming mode, but it is not used to unlock the door. The lock is programmed with the default mastercode 0-0-0-0. Replace this with a code of your own. The mastercode must be 4-10 digits. Keep door open and unlocked during programming.

How do I change my Powerbolt 2 code?

How do I add/delete a user code on my Powerbolt 2?

  1. Make sure the lock is unlocked and the door is open.
  2. Enter your Mastercode – for new install, default is 0-0-0-0.
  3. Press the lock button.
  4. Press 1.
  5. Press the lock button.
  6. Enter a new User Code.
  7. Press the lock button.
  8. Test the code: While your door is open, lock it.

How do you unlock a Kwikset Powerbolt 2?

Press and hold the “Reset” button for 5 seconds. You will hear 3 long beeps after the 5 seconds is completed indicating the lock has been reset. A User Code is used to unlock the door while a Mastercode is a password for making changes to the lock features.

How do I change the code on my Weiser Powerbolt 2?

How do I change the mastercode on my Powerbolt 2?

  1. Make sure the lock is unlocked and the door is open.
  2. Enter your Mastercode – for new install, default is 0-0-0-0.
  3. Press the lock button. You will hear one beep.
  4. Press 7.
  5. Press the lock button. You will hear one beep.
  6. Enter a new Mastercode.
  7. Press the lock button.

How do you take the code off a Weiser lock?

While the door is open, test the user code to make sure it no longer unlocks the door. 2 Press Lock button once. 4 Press Lock button once. 3 Enter user code to be deleted.

How do you unlock a Weiser keypad lock?

keyless entry- lock or unlock at the touch of a button.

  1. The door is now locked. To unlock the door, touch the.
  2. SecureScreen™ Touch the numbers in any order. to display the full touchscreen.
  3. Enter your code. Enter the access code.
  4. Wrong code. Enter the access code.
  5. The door is now unlocked. Tap the lock button to start over.

How do you lock a Weiser Powerbolt 2?

The lock will beep and the keypad will turn green or red. Press the Lock button. The latch bolt will extend to lock. Enter the default User Code (1-2-3-4), then press the Lock button.

How to set keyless entry on Powerbolt 2?

Programming Instructions 2 Powerbolt 2 Touchpad Keyless Entry Step 2: Set locking and unlocking direction 1. Make sure the door is open and in the unlocked position. 2. Press 0 – 0 – 0 – 0 – –00 – Note: Each button represents two numbers (i.e. ONLY push the button once for 0). If

What kind of lock is the Powerbolt 2?

Powerbolt 2 Electronic Lock – Brass Product Family Powerbolt Product Type Electronic Lock Product Style Traditional ANSI/BHMA 3 Microban No

How to enter master code on Powerbolt 2?

Programming Instructions 4 Powerbolt 2 Touchpad Keyless Entry 1. Make sure the door is open and in the unlocked position. 2. Enter the default Master Code 0 – 0 – 0 – 0 – – 7 – 3. Enter a 4 to 10 digit code and press 4. The lock will beep twice and the keypad will flash Green